Lock Picking 101 Forum
A community dedicated to the fun and ethical hobby of lock picking.
       

Lock Picking 101 Home
Login
Profile
Members
Forum Rules
Frequent Forum Questions
SEARCH
View New Posts
View Active Topics


Live Chat on Discord
LP101 Forum Chat
Keypicking Forum Chat
Reddit r/lockpicking Chat



Learn How to Pick Locks
FAQs & General Questions
Got Beginner Questions?
Pick-Fu [Intermediate Level]


Ask a Locksmith
This Old Lock
This Old Safe
What Lock Should I Buy?



Hardware
Locks
Lock Patents
Lock Picks
Lock Bumping
Lock Impressioning
Lock Pick Guns, Snappers
European Locks & Picks
The Machine Shop
The Open Source Lock
Handcuffs


Member Spotlight
Member Introductions
Member Lock Collections
Member Social Media


Off Topic
General Chatter
Other Puzzles


Locksmith Business Info
Training & Licensing
Running a Business
Keyways & Key Blanks
Key Machines
Master Keyed Systems
Closers and Crash Bars
Life Safety Compliance
Electronic Locks & Access
Locksmith Supplies
Locksmith Lounge


Buy Sell Trade
Buy - Sell - Trade
It came from Ebay!


Advanced Topics
Membership Information
Special Access Required:
High Security Locks
Vending Locks
Advanced Lock Pick Tools
Bypass Techniques
Safes & Safe Locks
Automotive Entry & Tools
Advanced Buy/Sell/Trade


Locksport Groups
Locksport Local
Chapter President's Office
Locksport Board Room
 

Home made key code cutter

Got a question about key machines? not sure what to buy? need a user manual? have some tips for keeping one running well or need help cutting or programming keys? Post here!

Re: Home made key code cutter

Postby MBI » 26 Nov 2013 8:59

I've seen a lot of folks want to make a home-made key cutter over the years, but this is by FAR the best one (and one of the only successful ones). Very nice you had the most expensive parts already laying around.
MBI
Moderator Emeritus
 
Posts: 1346
Joined: 9 Oct 2007 2:29
Location: Utah, USA

Re: Home made key code cutter

Postby ckc123 » 27 Nov 2013 13:19

fgarci03 wrote:Would you care to post a full tutorial on this? :P And maybe a video of a key being cutted?


I have a few more improvements to do before I post a lot more on it..

I'm going to add an LCD screen so you don't need a PC connected, and add controls to the cutter motor (on/off) and the attached vaccum (really helps cut down on the dust).
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby ckc123 » 1 Dec 2013 10:59

Ok.. Order some more "production" level boards and switches, but in the meantime I hacked together some stuff so I can write the code while I'm waiting..

Here it is.. it can now stand alone and be configured via the buttons/LCD screen

Here is the hardware pics

Wide Angle
Image

Stepper Motors / carrier
Image

Motor Mount
Image

Key in Cutter
Image
Image

Main Arduino Board
Image

Motor Driving Board
Image

Button Control Board
Image


Startup Screen
Image

Display the startup Toggle buttons on button board (Master Key Cut, Load Key, Eject Key, Wiggle feature for slightly wider cuts)

Image

Main default menu (to start the cutting via the menu)

Image

Optional button to immediately start cutting (eg bulk cutting where you don't what to have to press any menu buttons.)

Image

Moving the Carriage
Image
Image

Setting the KeyType and Depths to Cut
Image
Image
Image
Image

Thats it!!!
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby jeffmoss26 » 1 Dec 2013 17:45

Very impressive!!
"I tried smoking a blank once. I was never able to keep the tip lit long enough to inhale." - ltdbjd
jeffmoss26
 
Posts: 1090
Joined: 13 Jan 2012 15:01
Location: Cleveland, OH

Re: Home made key code cutter

Postby fgarci03 » 2 Dec 2013 14:05

THAT-IS-SO-COOL!

Thanks for posting the pics! I am inspired :mrgreen:
Go ahead, keep plugging away, picking on me! You will end up on bypass or with rigor mortise.
- GWiens2001
fgarci03
 
Posts: 1009
Joined: 18 Dec 2012 21:38
Location: Porto/Portugal

Re: Home made key code cutter

Postby ckc123 » 2 Dec 2013 14:09

fgarci03 wrote:THAT-IS-SO-COOL!

Thanks for posting the pics! I am inspired :mrgreen:


if your interested, I know where you can pick up another of those stages for about $100. ;)
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby fgarci03 » 2 Dec 2013 14:57

Well I don't have money for these kind of projects atm..
But it's very nice of you, thanks :wink:

Would posting the code be asking too much?
I completely understand if you want to keep it to yourself, for obvious reasons! But if you feel like it, it would be a nice way for us to understand how it works!
Go ahead, keep plugging away, picking on me! You will end up on bypass or with rigor mortise.
- GWiens2001
fgarci03
 
Posts: 1009
Joined: 18 Dec 2012 21:38
Location: Porto/Portugal

Re: Home made key code cutter

Postby ckc123 » 2 Dec 2013 21:28

I have no problem posting the code ( and the list of parts needed) for anyone who is interested.

once I can get it in a bit better shape (and finish up a few tweaks) I''ll put it online..
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby Nitrous » 3 Dec 2013 16:44

ckc123 wrote:I have no problem posting the code ( and the list of parts needed) for anyone who is interested.

once I can get it in a bit better shape (and finish up a few tweaks) I''ll put it online..


Really a great looking job! Thanks for sharing this.
I've done some research on the cutters that might interest you.

I believe you're using a symmetrical, biaxial cutter. That is fine for large cylinders, but if you want to cut smaller keys I.e. Master Padlock or automotive keys, you'll need an asymmetric cutter. Otherwise, there is a risk of cutting into the shoulder, if the first cut is deep.

If you look at the Blitz, you'll see the cutter for small cylinders us an 1101. This is an asymmetrical, biaxial milling cutter.

The Ilco 029A is a dual function duplicator, code cutter but I believe it's primarily for automotive work. The cutter is a CU29. Again, it's biaxial (cuts on both sides of the disc) but is asymmetrical (the cutting surface on both sides of the disc are not equal) allowing the cutter to get close to the shoulder of the blank.

These cutters also have a "flat" aspect the gives the bottom pin a suitable place to seat. They are available on ebay for $50 or $60.

Again, great job.

Nitrous
Nitrous
 
Posts: 65
Joined: 8 Nov 2012 20:26

Re: Home made key code cutter

Postby ckc123 » 3 Dec 2013 17:11

Nitrous wrote:I believe you're using a symmetrical, biaxial cutter. That is fine for large cylinders, but if you want to cut smaller keys I.e. Master Padlock or automotive keys, you'll need an asymmetric cutter.


Nitrous.. you raise a very good point..

The code that I wrote will work for an asymmetric cutter. (while it's not used now).. it can perform a "traveling cut" and not just a straight "plung". you would use the traveling cut for the small pin.. just like a key copier..

the hard part is just determining the vector for each transition from space to space. (but it's just math, so as I used to say at work.. it's just 1 & 0's you just have to line them up in the right order..)
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby Nitrous » 3 Dec 2013 22:30

ckc123 wrote:
Nitrous wrote:I believe you're using a symmetrical, biaxial cutter. That is fine for large cylinders, but if you want to cut smaller keys I.e. Master Padlock or automotive keys, you'll need an asymmetric cutter.


Nitrous.. you raise a very good point..

The code that I wrote will work for an asymmetric cutter. (while it's not used now).. it can perform a "traveling cut" and not just a straight "plung". you would use the traveling cut for the small pin.. just like a key copier..

the hard part is just determining the vector for each transition from space to space. (but it's just math, so as I used to say at work.. it's just 1 & 0's you just have to line them up in the right order..)


I understand the idea of a travelling cut but the flat on the first cut needs to be a fixed distance from the shoulder of the blank. If the depth of cut is deep enough, the shoulder side of the biaxial cutter will have to cut into the shoulder. That is the problem that an asymmetric cutter solves. In fact, the use of traveling rather than plunge cuts with the asymmetric cutter is likely the best of both worlds.

Maybe I'm missing something.

Nitrous
Nitrous
 
Posts: 65
Joined: 8 Nov 2012 20:26

Re: Home made key code cutter

Postby ckc123 » 3 Dec 2013 22:39

Well the way I understand it.. the MACS prevents each of the cuts for a single cut to interfere with another, and with the shoulder itself. (which is why the 1st cut is further than the first to first cut) you can't have the first cut go past the shoulder if you are using the correctly angled cutter (now is you use a 100 when the spec is a 90, then you would.. but then again you try to stay away from having the first cut being the deepest on a key anyways since it will be the "weak point" in the key if it does break in the lock etc..

but regardless. any key cutting machine if it uses an asymmetric cutter can cut a nice 90 degree cut on the shoulder if
ckc123
 
Posts: 195
Joined: 2 Jan 2011 21:49
Location: North of the GTA

Re: Home made key code cutter

Postby HeadHunterCEO » 4 Dec 2013 17:13

That is excellent
Doorologist
HeadHunterCEO
 
Posts: 1262
Joined: 7 Apr 2004 21:10
Location: NY,NY

Re: Home made key code cutter

Postby Nitrous » 4 Dec 2013 18:19

ckc123 wrote:Well the way I understand it.. the MACS prevents each of the cuts for a single cut to interfere with another, and with the shoulder itself. (which is why the 1st cut is further than the first to first cut) you can't have the first cut go past the shoulder if you are using the correctly angled cutter (now is you use a 100 when the spec is a 90, then you would.. but then again you try to stay away from having the first cut being the deepest on a key anyways since it will be the "weak point" in the key if it does break in the lock etc..

but regardless. any key cutting machine if it uses an asymmetric cutter can cut a nice 90 degree cut on the shoulder if


Not sure how MACS will affect the first cut vs the shoulder of the key. If you have a MACS of 4 and the first cut is 4 or greater, you'll certainly cut into the shoulder (on a small cylinder key) with a 90 degree symmetrical cutter. But a 4 cut will still hit the shoulder if the MACS is 7 or 3.

I don't believe MACS factor into the first cut (although most wouldn't recommend a really deep cut next to the shoulder, but that is to reduce risk of weakening the blank).

If I'm wrong on this, please correct me. I agree with you that an asymmetric cutter like an 1102 or CU29 will not interfere with the shoulder.

Nitrous
Nitrous
 
Posts: 65
Joined: 8 Nov 2012 20:26

Re: Home made key code cutter

Postby Nitrous » 4 Dec 2013 18:31

Just one more thought on the "any asymmetric cutter will produce a nice 90 deg at the shoulder" comment.

If you have a regular size cylinder, a deep plunge cut with a CU29 will give a nice 45 deg cut on the tip side of the key, but a 90 deg shoulder on the top of the cut on the bow side. That's fine with a first cut, but I think it could create some problems inserting the key. If the key manages to get in, it would come out nicely, but those 90 deg bow side cuts might be a real problem.

Nitrous
Nitrous
 
Posts: 65
Joined: 8 Nov 2012 20:26

PreviousNext

Return to Key Machines & Programmers

Who is online

Users browsing this forum: No registered users and 0 guests